Securitron

Power plus interfaces for sophisticated access control. The PDB-8F8R and PDB-8C8R split a power supply main output into eight fused- or PTC circuit breaker-protected outputs. Each output is individually configurable to respond and react to access control relay inputs and/or fire trigger.

Features:

• 8 Heavy duty relays with individual Inputs and status LED’s
• Each relay input can be activated from low current open collector, normally closed or normally open switch
• EOL End of line resistor fire interface master trigger de-energizes all output relays that are enabled
• Universal 12 – 28VDC power input (nominal 12-24VDC)
• 8C8R is Class 2 power limited
• Class 1 wiring required for 8F8R unless powered by a UL 294 or UL 603 or ULC S318 or ULC S533 listed power supply with class 2 output. There shall be a min of ¼ separation between power limited and non-power-limited circuits.
• Available with fuses or PTC circuit breakers
• Each output may be individually configured for: Fire trigger (FT) enabled or (FTD) disabled N/O or N/C option configures the relay switched output.
• Each output 1-8 has a protected, continuous output and a relay controlled output
• Control power and main lock power may be isolated (separate power supplies) at users option

Specifications:

• Control (- CONTR +): 12–24VDC @ 37mA
• Main Power (-power+): 12-28VDC (12-24 VDC nominal)
• Max. Output Current 2A variants: 2A per port / total 16A
• 7Max. Output Current 1A variants: 1A per port; total 8A
• Dry Outputs (Models 8F8R only): 3A, 30VDC; 3A, 250VAC resistive load.
• Terminal blocks un-pluggable: 5mm spacing 14–22 awg
• PTC Rating Outputs 1-8: 2.5A for 2A variants, 1.1A for 1A variants
• Glass Fuse Rating Output 1-8: 2A,250VAC ; 1A,250VAC
• Dimensions: 14" x 14" x 4-3/4" [355.6mm x 355.6mm x 120.65mm]
• Normally no connection is made here. Note: Dual/separate power source configuration has not been evaluated by UL and cannot be configured for UL listed products.
• Note: Must cut J1 & J2 when not using 12-24VDC power see dual/separate power source configuration
• Total power supply draw would be equal to the total current of the outputs load plus the module draw of 37mA
• Note: Wires should be properly sized based on output load
• Caution: For continued protection against risk of fire, replace only with fuse of the same type and having the same electrical ratings.
• The fused outputs of the PDB-8F8R are power limited only when connected a UL listed power-limited power supply
• Note: The unit shall be installed in accordance with the National electrical code, ANSI/NFPA 70; Canadian electrical code, or any other applicable codes.
• Note: For UL compliance unit shall be installed in a suitable enclosure that is listed to UL 603 or UL 294 or ULC-S318 or ULC-S533.
• Note: All interconnected devices must be UL listed.

Models:

• PDB-1R: Fire trigger / relay interface board
• PDB-4F1: PDB, 4 output, 1A glass fuse
• PDB-4F2: PDB, 4 output, 2A glass fuse
• PDB-4C1: PDB, 4 output, 1A PTC
• PDB-4C2: PDB, 4 output, 2A PTC
• PDB-8F1: PDB, 8 output, 1A glass fuse
• PDB-8F2: PDB, 8 output, 2A glass fuse
• PDB-8C1: PDB, 8 output, 1A PTC
• PDB-8C2: PDB, 8 output, 2A PTC
• PDB-8F8R1: PDB, 8 relayed outputs, 1A glass fuse
• PDB-8F8R2: PDB, 8 relayed outputs, 2A glass fuse
• PDB-8C8R1: PDB, 8 relayed outputs, 1A PTC
• PDB-8C8R2: PDB, 8relayed outputs, 2A PTC
• PDB-8C1R1: PDB, 8 output w/ fire trigger relay, 1A PTC
• PDB-8C1R2: PDB, 8 output w/fire trigger relay, 2A PTC
• PDB-8F1R1: PDB, 8 output w/ fire trigger relay, 1A glass fuse
• PDB-8F1R2: PDB, 8 output w/fire trigger relay, 2A glass fuse